A UNIQUE AND CONVENIENT WAY TO CARRY DICE WITH YOU
Who doesn't love a good dice game between friends? We often enjoy playing dice around the shop, at parties, road trips, whenever.
With that in mind we came up with a really unique and convenient way to carry dice with you wherever you go. And not just any dice but official Lowbrow Customs Dice! These were made for us in Warsaw, Poland, the ancestral land of half of Tyler & Kyle's family.
Lowbrow dice come in two different colors: black and green marbled or white and grey marbled. You can purchase either color in sets of 3 with the keychain holder or in sets of 10 for those real gamers out there. This is just good old fashion fun for everyone!
WATCH VIDEO: DICE KEYCHAIN HOLDER ASSEMBLY HOW-TO
As said by a friend, this Lowbrow Dice Keychain Holder set gives you "a little craft experience" to go along with your purchase. The laser cut aluminum dice holder requires assembly.
It's simple (and fun), bit we made you this video walking you through how to assemble your new keychain holder. With a couple simple hand tools and a few minutes of your time, you will instantly become one of the coolest and luckiest people in the world.
Well, we can't really guarantee the lucky part but you will be pretty cool whipping out them dice like a wizard doing wizardry type things at a party.
Your new Lowbrow Customs Dice Keychain Holder will come flat in the packaging like this and will require some simple folding.
ASSEMBLE DICE KEYCHAIN HOLDER IN 5 EASY STEPS
STEP 1: BENDING THE KEY HOLE TABS
Hold the metal plate in your hand with the lightning bolt on your left so you can read the letters "LBC" left to right. Locate the keyhole tabs on the top of the lightning bolt and letter "B" panel.
Locate the first slit on the key hole tab closest to the letters on the plate and use a set of flat nose pliers bend the key hole tabs away from you toward the back of the plate close to 90 degrees.
Bend at the first slit closest to the letters where the key ring will go, bend both tabs back about 90 degrees away from you towards the back of the plate.
Bending the second tab again from the first slit closest to the lightning bolt away from you towards the back of the plate at about 90 degrees.
Next bend the second slit on the key hole tabs the opposite direction back towards yourself at 90 degrees so it is even / parallel with the front of the plate.
Locate the second slit on the key hole tabs above the letter "B" and lightning bolt.
Bend the key hole tab from the second slit back towards yourself to 90 degrees and make both of them even / parallel with the front of the plate.
STEP 2: FOLDING TO CREATE A SQUARE
We found this next step to be easier if you start at the letter "C" panel. Using your hands, fold the letter "C" panel away from you towards the "B" panel so that it meets at a 90 degree angle with the key hole tab you just bent. When it hits that will indicate you have bent it fully.
Start at the letter "C" panel on the right side. 
Using your hands fold over the "C" panel towards the "B" panel until it hits the top key hole tab you just bent which will indicate it to 90 degrees.
Repeat the same step but now from the letter "B" panel. Use your hands and bend the "B" panel inward to the "L" panel. Again it will stop once it his the top key hole tab you bent at 90 degrees.
Bending "B" panel to the "L" panel 90 degrees.
Your keychain dice holder should now look something like this, 3 parts of a square should be made.
STEP 3: LOCK THE BODY TOGETHER
On the middle of the "C" panel you will see a small tab on the side left open. This will interlock with the larger tab on the lighting bolt side once you bend the two together. Using your hands bend the two together and interlock those tabs.
You can see here the two tabs that will lock together once you bend the "C" panel into the lightning bolt panel.
Using your hands bend over the lighting bolt panel onto the "C" Panel and squeeze firmly. The two tabs on the sides will link together.
Using the flat nose pliers bend the two tabs opposite of each other.
Gently use a small hammer to flatten the two tabs down to the sides of the keychain holder.
This is the way yours should look ones the tabs are hammered down.
Next take the corner where the letter "C" panel and lightning bolt panel met and the opposite corner and give it a squeeze to make sure the keychain holder looks square.
Give her a squeeze at the seem and opposite corner to make sure its square.
STEP 4: ADD THE DICE, RUBBER CAP, AND KEY RING
It's now time to insert those dice into your holder. This ones pretty simple guys, they literally only go in one way.
Put those dice in the holder anyway you want.
Slide the boot over the bottom of the holder and give it a shake to be sure its on tight.
Muscle that key ring into the key hole tab. Use your pliers if you need to.
Slap that bad boi on your keys, carabiner, or whatever you want, the world is your oyster!
STEP 5: THROW SOME DICE BABY!
What's $100 amongst friends?
Words & Video by: Mikey Revolt
Related Products
